Vaderstad Rapid RDA 400S Original Instructions Manual Download Page 49

Page: 49 / 138

RDA 400S

27.06.2011
ver.2

5 To access the calibration menu, depress the

button on the Control Station.

(Alternatively, the calibration menu can be called up by simultaneously depressing the

and

buttons on the Control Station.)

Figure 3.55

Use the dial to select a row in the menu, mark the row and press

to confirm.

6 Mark the menu row

with

. Enter the desired output volume in kg/hectare. Confirm

with

7 Mark the menu row

with

. Enter the desired increase/decrease of the output vol-

ume as a percentage for the electrically adjustable sown amount. Confirm with

8 Scroll down to the menu row “Calibrate” and depress

Figure 3.56

9 Fill the seed output system by depressing the

button above the

button. Alterna-

tively, the corresponding button on the remote control can be used.

Empty the calibration bag.

Summary of Contents for Rapid RDA 400S











































































































































Search results

Summary of Contents for Rapid RDA 400S

Reviews:

Related manuals for Rapid RDA 400S

Brands by name

Popular brands

Vaderstad Rapid RDA 400S, Original Instructions Manual

Search results

Summary of Contents for Rapid RDA 400S

Reviews:

Related manuals for Rapid RDA 400S

Brands by name

Popular brands