Vaderstad Rapid RDA 400S Original Instructions Manual Download Page 42 | Manualshive

Page: 42 / 138

background image

Instructions and settings

42

27.06.2011

ver. 2

3.18 Scraper

Figure 3.42

The scraper default settings are shown in the figure.

The scraper position can be adjusted in two places. If the setting (A) is insufficient, the holder (B)
can be adjusted lengthwise.

NOTE!

The distance (C) between the scraper blade and the tyre must not be less than 5 mm. Rotate

the tyre by hand to verify that this distance is not less than 5 mm at any point.

!

Depending on the circumstances, a larger distance (C) may be required for optimum results. If
the scraper does not operate satisfactorily, then try with different scraper settings.

Example:

- If there are a lot of plant residues in the soil and it is humid, the scraper will usually provide
better results when the distance (C) is increased to approx. 20 mm.

- If the soil is humid without plant residues, the scraper will provide better results when mount-
ed in the default position (C = 5 mm).

B

A

C=5 mm

«
...
40
41
42
43
44
...
»

Summary of Contents for Rapid RDA 400S











































































































































Reviews:

No comments

Related manuals for Rapid RDA 400S

Brand: UnionSpecial Pages: 56

Brand: Wahl Pages: 2

Brand: V-TAC Pages: 13

Brand: Jackson Pages: 2

Brand: Vag Pages: 10

Cell Saver Elite+

Brand: Haemonetics Pages: 230

Brand: GE Pages: 37

Brand: BH FITNESS Pages: 24

Brand: Best Fitness Pages: 26

Water Inlet Suction Hose

Brand: Nilfisk-Advance Pages: 8

Brand: TRX Pages: 2

Brand: Floe Pages: 12

Brand: Rottler Pages: 96

Brand: WIFO Pages: 24

Brand: Foxfury Lighting Solutions Pages: 17

Brand: Halemeier Pages: 2

Brand: IRUDEK Pages: 19

Brand: Baileigh Industrial Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands