Vaderstad Rapid RDA 400S Original Instructions Manual Download Page 62

Page: 62 / 138

Instructions and settings

27.06.2011

ver. 2

Information

Press

to access the information menu. Advance by turning the knob. If an alarm simulta-

neously appear on the Control Station, the alarm texts are shown first.

The information menu shows: seed trip meter (kg),

, trip area meter (ha),

, trip seasonal

area meter (ha),

, trip total area meter (ha),

, speedometer (average speed in km/h),

, and the total timer (h),

It is not possible to reset the trip total area meter, speedometer and the total timer.

The other meters can be reset by first selecting the row where

is displayed and then pressing

The information texts are shown last in the menu. The texts below may appear on this machine:

- Low-lift switch engaged.

- Unfolding switch engaged.

NOTE!

The seed trip meter (kg),

, displays the theoretical value for the output seed amount.

This value may differ slightly from the actual sown amount.

Summary of Contents for Rapid RDA 400S











































































































































Search results

Summary of Contents for Rapid RDA 400S

Reviews:

Related manuals for Rapid RDA 400S

Brands by name

Popular brands

Vaderstad Rapid RDA 400S, Original Instructions Manual

Search results

Summary of Contents for Rapid RDA 400S

Reviews:

Related manuals for Rapid RDA 400S

Brands by name

Popular brands