Vaderstad Rapid RDA 400S Original Instructions Manual Download Page 57

Page: 57 / 138

RDA 400S

27.06.2011
ver.2

3.30.1

Functional description

1 Main switch

- Activation of the Control Station when starting.

- Master stop (all feeding stops and "STOP" is displayed on the 3rd and 4th row)

Calibration

4 Not used

5 LCD display

6 Tramlining indicator lamps

Off = No tramlining

Green light = Tramlining and correct operation

Red light = Incorrect tramlining

7 - Auto advance block. The indicator lamp next to the button lights when the block is engaged.

- Selection of tramlining programme (Keep the push-button pressed for 5 seconds)

8 Manual advance of tramlining.

9 Indicator lamps for active bout markers.

10 Manual selection of bout markers. Both in/left out/right out/both out.

11 - Automatic bout marker change left/right. The indicator lamp next to the button lights when

automatic operation is engaged.

- Manual change of bout marker.

12 Information. Used to explain alarm conditions, to check the trip meter, average speed, etc.

13 Enter

14 Escape

15 Selection of low-lift or full lift. The indicator lamps next to the button show which function has

been engaged. The left indicator lamp blinks when the low-lift switch has been engaged.

16 Lift stop Used to operate bout markers without raising the machine from the furrow.

17 Selection dial. Use the dial to page through the menus. Selections are shown against a dark

background. Use

to confirm a selection and then use the dial to select or change the value

of the selected item. Confirm the value/selection with

When entering digits, the speed of change upwards/downwards can be increased by keeping

depressed while turning the dial.

18 Shut-off of seed feeding

19 Not used

20 Not used

Summary of Contents for Rapid RDA 400S











































































































































Search results

Summary of Contents for Rapid RDA 400S

Reviews:

Related manuals for Rapid RDA 400S

Brands by name

Popular brands

Vaderstad Rapid RDA 400S, Original Instructions Manual

Search results

Summary of Contents for Rapid RDA 400S

Reviews:

Related manuals for Rapid RDA 400S

Brands by name

Popular brands