Toshiba TOSVERT VF-FS1 Series, Instruction Manual

Page: 203 / 252

E6581381
J-1
10
10. Peripheral devices
Danger
Mandatory
•
When using switchgear for the inverter, it must be installed in a cabinet.
Failure to do so can lead to risk of electric shock and can result in death or serious injury.
Be Grounded
•
Connect earth cables securely.
Failure to do so can lead to risk of electric shock or fire in case of a failure or short-circuit or electric
leak.
10.1 Selection of wiring materials and devices
Wire size (See Note 4)
Power circuit
(mm 2 ) Note 1)
Earth cable
(mm 2 )
Voltage
class
Capacity of
applicable motor
(kW)
Inverter model
For IEC60364-5-
523/54
For JAPAN
JEAC8001-1995
For IEC60364-5-
523/54
For JAPAN
JEAC8001-1995
0.4 VFFS1-2004PM 1.5 2 2.5 2
0.75 VFFS1-2007PM 1.5 2 2.5 2
1.5 VFFS1-2015PM 1.5 2 2.5 2
2.2 VFFS1-2022PM 1.5 2 2.5 2
4.0 VFFS1-2037PM 2.5 2 2.5 2
5.5 VFFS1-2055PM 4 3.5 4 3.5
7.5 VFFS1-2075PM 6 5.5 6 3.5
11 VFFS1-2110PM 10 14 10 5.5
15 VFFS1-2150PM 16 14 16 5.5
18.5 VFFS1-2185PM 25 22 16 8
22 VFFS1-2220PM 25 38 16 8
Three-phase
200V class
30 VFFS1-2300PM 50 38 25 14
0.4 VFFS1-4004PL 1.5 2 2.5 2
0.75 VFFS1-4007PL 1.5 2 2.5 2
1.5 VFFS1-4015PL 1.5 2 2.5 2
2.2 VFFS1-4022PL 1.5 2 2.5 2
4.0 VFFS1-4037PL 1.5 2 2.5 2
5.5 VFFS1-4055PL 1.5 2 2.5 2
7.5 VFFS1-4075PL 1.5 2 2.5 2
11 VFFS1-4110PL 4 3.5 4 3.5
15 VFFS1-4150PL 6 5.5 6 3.5
18.5 VFFS1-4185PL 6 5.5 6 5.5
22 VFFS1-4220PL 10 8 10 5.5
Three-phase
400V class
30 VFFS1-4300PL 16 14 16 5.5
Note 1: Sizes of the wires connected to the input terminals R/L1, S/L2 and T/L3 and the output terminals U/T1,
V/T2 and W/T3 when the length of each wire does not exceed 30m.
Note 2: For the control circuit, use shielded wires 0.75 mm 2 or more in diameter.
Note 3: For grounding, use a cable with a size equal to or larger than the above.
Note 4: The wire sizes specified in the above table apply to HIV wires (cupper wires shielded with an insulator
with a maximum allowable temperature of 75°C) used at an ambient temperature of 40°C or less.
Note 5: If there is a need to bring the inverter into UL compliance, use wires specified in Chapter 9.