manualshive.com logo in svg

Teledyne LeCroy T3DSO2000A Series, User Manual

Share
Download
Teledyne LeCroy T3DSO2000A Series User Manual Download Page 42

T3DSO2000A Manual. Page 38

A. Digital channel waveform display, which shares the same grid area with the analog

channels.

B. Digital channel descriptor box

C. Dialog box

D. Digital channel indicators. Up to 16 digital channels are organized in two groups with

different thresholds: D15~D8 and D7~D0. Every channel can be turned on or off
individually.

E. Labels can be set to data, address or custom characters.

From the Front Pane

l

Press the Digital button on the front panel to turn on digital channels and display the
waveforms. Press again to turn off.

From the Touch Screen

Click + at the bottom of the display and select the "Digital" to turn on; click the digital
channel descriptor box, and clicking Off on the pop-up menu to turn off. Refer to the
operation in the chapter "Vertical Setup" for details.

13.3 Digital Channel Setup

Touch the digital descriptor box, then the quick menu of digital channel settings pops up
above the descriptor box. In the menu height and position of digital channels can be set:

A. Upper position limit of the digital channel display

area. You can use the universal knob or virtual
keypad to set it. Decrease the height to provide
more adjustment area.

B. ▲ to increase position and ▼ to decrease the

channel location.

C. Reset the position to default value

D. The range in height of the digital channels display

area. You can use the universal knob or virtual
keypad to set it. If the display height covers all of
the available divisions, there will not be room to
adjust the position.

E. ▲ to increase and ▼ to decrease the number of

divisions occupied by the digital channels

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for LeCroy T3DSO2000A Series










































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands