manualshive.com logo in svg

Teledyne LeCroy T3DSO2000A Series, User Manual

Share
Download
Teledyne LeCroy T3DSO2000A Series User Manual Download Page 40

T3DSO2000-LS Probe

The T3DSO2000-LS is a logic probe designed to monitor up to 16 digital signals at once.
The 16 digital channels are separated into two groups and each group has its own
threshold, making it possible to simultaneously view data from different logic families.

Note: To avoid personal injury or damage to the logic probe and any associated
equipment, the following safety precautions should be noted.

The equipment shall be used only for the purposes specified by the manufacturer. The
T3DSO2000-LS probe is used only for Teledyne Test Tools series of oscilloscopes.
Protection mechanisms can be compromised if the way the devices connected by the
T3DSO2000-LS are not used for their intended purpose.

Connect and disconnect correctly. Excessive bending can damage the cable.

T3DSO2000A Manual. Page 36

13 Digital Channels

13.1 Overview

!

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for LeCroy T3DSO2000A Series










































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands