manualshive.com logo in svg

Teledyne LeCroy T3DSO2000A Series, User Manual

Share
Download
Teledyne LeCroy T3DSO2000A Series User Manual Download Page 149

T3DSO2000A Manual. Page 145

A. Menu bar

B. Coordinate of the latest touched point on the display

C. Mask edit area, which is equivalent to the grid area. In this example, a hexagon has
been created as a part of the mask

D. Toolbar

E. Coordinate edit area. Set the X ordinate and Y ordinate by the virtual keypad and
then touch the “Input” button the perform the ordinate update

F. Display or hide coordinate of polygon vertices on the display

G. Exit the tool

Menu bar

There are 2 menus on the menu bar. The File menu includes ordinary file operations
such as:

•

New: Create a new mask file

•

Open: Open an existed mask file

•

Save: Save the current mask file

•

Exit: Exit the Mask Editor tool

Note: The mask file created by the “Create Mask” cannot be recalled by the Mask Editor.

The contents of the Edit menu are equivalent to the Toolbar.

Toolbar

Draw: Creates vertices of a polygon by touching the display or entering values in
coordinate edit area

Create Polygon: Creates a polygon based on the drawn vertices by the operation
Draw

Undo

Redo

Insert Point: Inserts a vertex on a selected side

Edit Polygon: Edits a polygon. Vertices, sides and the polygon are all editable
objects

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for LeCroy T3DSO2000A Series










































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands