manualshive.com logo in svg

Teledyne LeCroy T3DSO2000A Series, User Manual

Share
Download
Teledyne LeCroy T3DSO2000A Series User Manual Download Page 191

T3DSO2000A Manual. Page 187

30.4 Language

The T3DSO2000A supports multiple languages, including: Simplified Chinese,
Traditional Chinese, English, French, Japanese, German, Spanish, Russian, Italian and
Portuguese.

Operate Utility>System Setting>Language, and select the language in the list.

30.5 Screen Saver

The screen saver will be activated if the oscilloscope has not been operated for a set
period of time. At this time the backlight of the display is cut off to save power
consumption.

Operate Utility>System Setting>Screen Saver to specify the period before screen saver,
or select "Off" to disable the screen saver.

Any action from the mouse, touch screen or front panel can disable the screen saver.

30.6 I/O Setting

30.6.1 LAN

Operate the following steps to set the LAN port:

Perform Utility>System Setting>I/O Setting>LAN Config to open the LAN Config dialog
box.

A. Check Automatic (DHCP) to enable dynamic

IP. In this case, the oscilloscope must be
connected to the local area network with a
DHCP server. Contact your network
administrator to confirm the relevant
information.

B. When is not checked, the oscilloscope uses

static IP. Set the static IP address, subnet
mask, and gateway separately.

C. MAC address of the oscilloscope, read only.

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for LeCroy T3DSO2000A Series










































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands