manualshive.com logo in svg

Teledyne LeCroy T3DSO2000A Series, User Manual

Share
Download
Teledyne LeCroy T3DSO2000A Series User Manual Download Page 11

T3DSO2000A Manual. Page 6

19.4 FREQUENCY ANALYSIS ................................................................ 125

19.5 FORMULA EDITOR ........................................................................ 132

20 REFERENCE ..................................................................................... 133

21 SEARCH ............................................................................................ 134

22 NAVIGATE ......................................................................................... 137

23 MASK TEST ....................................................................................... 141

23.1 OVERVIEW ..................................................................................... 141

23.2 MASK SETUP ................................................................................. 143

23.2.1 Create Mask ................................................................................. 143

23.2.2 Mask Editor .................................................................................. 144

23.3 PASS/FAIL RULE ............................................................................ 146

23.4 OPERATION ................................................................................... 146

24 COUNTER .......................................................................................... 147

24.1 OVERVIEW ..................................................................................... 147

24.2 MODE .............................................................................................. 148

25 POWER ANALYSIS ........................................................................... 149

25.1 OVERVIEW ..................................................................................... 149

25.2 POWER QUALITY .......................................................................... 149

25.3 CURRENT HARMONICS ................................................................ 151

25.4 INRUSH CURRENT ........................................................................ 152

25.5 SWITCHING LOSS ......................................................................... 153

25.6 SLEW RATE .................................................................................... 155

25.7 MODULATION ................................................................................. 156

25.8 OUTPUT RIPPLE ............................................................................ 157

25.9 TURN ON/TURN OFF ..................................................................... 157

25.10 TRANSIENT RESPONSE ............................................................. 159

25.11 PSRR .............................................................................................160

25.12 POWER EFFICIENCY .................................................................. 161

26 BODE PLOT ........................................................................................ 162

26.1 OVERVIEW ..................................................................................... 162

26.2 CONFIGURATION ........................................................................... 163

26.2.1 Connection ................................................................................... 163

26.2.2 Sweep .......................................................................................... 163

26.3 DISPLAY ......................................................................................... 165

26.4 DATA ANALYSIS ............................................................................ 167

27 DISPLAY ............................................................................................ 169

28 ARBITRARY WAVEFORM GENERATOR ......................................... 175

28.1 OVERVIEW ..................................................................................... 175

28.2 OUTPUT .......................................................................................... 175

28.3 WAVE TYPE ................................................................................... 175

28.4 OTHER SETTING ........................................................................... 177

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for LeCroy T3DSO2000A Series










































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands