Teledyne LeCroy T3DSO2000A Series User Manual Download Page 189

Page: 189 / 201

T3DSO2000A Manual. Page 185

Fourth, touch Recall and wait for the oscilloscope to finish recalling the setup.

30 System Setting

Most of the system settings can be found in the Utility dialog box, such as system
status, language, sound, self-calibration, firmware upgrading.

30.1 System Status

Operate Utility>System Setting>System Status to check the system status. System
information includes the contents shown below.

30.2 Sound

Perform Utility>System Setting>Sound to enable or disable the audible buzzer.

：

Indicates the buzzer is on.

：

Indicates the buzzer is off.

30.3 Upgrade Software

The firmware is upgradeable through external USB memory devices/U disk. Make sure
the U disk contains the correct upgrade file (*.ads) is connected to the oscilloscope
before performing the upgrade.

Operate Utility>System Setting>Upgrade to recall the upgrade dialog box:

T3DSO2052A

T3DSO123456789

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for LeCroy T3DSO2000A Series










































































































































































































Search results

Summary of Contents for LeCroy T3DSO2000A Series

Reviews:

Brands by name

Popular brands

Teledyne LeCroy T3DSO2000A Series, User Manual

Search results

Summary of Contents for LeCroy T3DSO2000A Series

Reviews:

Brands by name

Popular brands