manualshive.com logo in svg

Teledyne LeCroy T3DSO2000A Series, User Manual

Share
Download
Teledyne LeCroy T3DSO2000A Series User Manual Download Page 183

T3DSO2000A Manual. Page 179

To Default Key

The oscilloscope provides two options for the default setting. When the Default Type is
set to “Factory”, the factory default setting will be recalled by pressing the Default button
on the front panel; When the Default Type is set to “Current”, the last setting saved by
the “To Default Key” operation will be recalled by pressing the Default button on the front
panel.

The following table shows the relationship between the save types and save/recall
operations.

*Save/Recall only supports saving Reference to external memory. However, the
reference waveform itself can be saved to internal memory. See the chapter
"Reference" for details.

29.2

Internal Save and Recall

"Setup" can be saved/recalled to/from the internal memory. In this section the save/
recall operations of Setup are introduced.

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for LeCroy T3DSO2000A Series










































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands