Teledyne LeCroy T3DSO2000A Series User Manual Download Page 142

Page: 142 / 201

T3DSO2000A Manual. Page 138

Navigate by History Frame

When the history function is turned on, Navigate can be used to play
history frames (see the chapter " History" for details of history
function).

Touch Type in the navigate dialog box to select the navigate type as
“History Frame”.

Touch Frame to set the frame number by the universal knob or the
virtual keypad.

Press the navigation buttons

◀

■

▶

on the front panel to play

backward, stop, or play forward.

Touch Playing Mode to set the search event playing mode.

Touch Interval Time to set the playing interval by the universal knob
or the virtual keypad.

Touch Stop On Search Event to set the stop play condition: stop
when the event is searched. This setting is only valid when the
search function is on.

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for LeCroy T3DSO2000A Series










































































































































































































Search results

Summary of Contents for LeCroy T3DSO2000A Series

Reviews:

Brands by name

Popular brands

Teledyne LeCroy T3DSO2000A Series, User Manual

Search results

Summary of Contents for LeCroy T3DSO2000A Series

Reviews:

Brands by name

Popular brands