manualshive.com logo in svg

Teledyne LeCroy T3DSO2000A Series, User Manual

Share
Download
Teledyne LeCroy T3DSO2000A Series User Manual Download Page 192

T3DSO2000A Manual. Page 188

30.6.2 VNC Port

When accessing more than two Teledyne Test Tools instruments through the web
browser, it is necessary to set a different VNC port number for each instrument.

Perform Utility>System Setting>I/O Setting>VNC Port to set.

Touch the VNC Port area and use the universal knob or the virtual keyboard to set the
port number, the range is from 5900 to 5999.

30.7 Date/Time

The T3DSO2000A has an RTC clock, which helps to record absolute time information
for screenshots, history frames and so on.

Operate Utility>System Setting> Date/Time to open the Date/Time dialog box:

Touch the text box of Hour, Minute, Second, Day, Month and Year to edit these fields.
Touch the Modify button to perform the change.

30.8 Install Options

The T3DSO2000A provides a few options to enhance its functionality. Contact your
local Teledyne Test Tools sales representative or Teledyne Test Tools technical support
to purchase the corresponding option key. Then perform the following steps to install the
option:

•

Go to Utility > Options where all option information can be viewed. When the option
is not activated, the license type is displayed as "Temporary" and can be used up to
30 times before disabling.

•

Select the option to install.

•

In the option key input area, touch or click the text box and enter the key using the
virtual keyboard.

•

Clear the characters in the key input area.

•

After entering the option key, click Install to perform the installation.

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for LeCroy T3DSO2000A Series










































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands