manualshive.com logo in svg

Teledyne LeCroy T3DSO2000A Series, User Manual

Share
Download
Teledyne LeCroy T3DSO2000A Series User Manual Download Page 134

T3DSO2000A Manual. Page 130

Horizontal Control

Touch Center Freq to set the center frequency of FFT waveform by the universal knob or
the virtual keypad.

Touch Hz/div to set the horizontal scale of FFT waveform by the universal knob or the
virtual keypad. The reference point for horizontal scale scaling is the center frequency.

FFT Tools

The T3DSO2000A provides two tools for FFT waveform: Peaks and Markers. The peaks
tool can automatically search the qualified peak points and mark them on the FFT
waveform. Up to 10 peaks are supported. Based on the peak Tool, the markers tool can
automatically search the qualified harmonics, and users can control the position of each
marker. Up to 8 markers are supported.

Touch Tools in the math dialog box to recall the FFT tools dialog
box:

When the FFT tool type is set to peaks, the dialog box is as follows:

A. Turn on or off the table. Turn on the table, the peaks searched

with the limit of Search Threshold and Search Excursion will be
displayed in table

B. Turn on or off the display of peak frequency in the table

C. Sort peaks by amplitude or frequency

D. Set the search threshold. Only peaks larger than the limit are

shown

E. Set the difference between the peak value and the minimum

amplitude on both sides. The difference should be greater than
the search excursion

F. Return to previous menu

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for LeCroy T3DSO2000A Series










































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands