manualshive.com logo in svg

Teledyne LeCroy T3DSO2000A Series, User Manual

Share
Download
Teledyne LeCroy T3DSO2000A Series User Manual Download Page 22

T3DSO2000A Manual. Page 18

8.3 Grid Area

The grid area displays the waveform traces. Traces can be moved by dragging and re-
scaled by pinch and spread. The area is divided into 8 (vertical) * 10 (horizontal) grids.
The best display effect can be obtained by adjusting the waveform intensity and
graticule. Follow the steps below to set these parameters:

Display

＞

Intensity

，

Display

＞

Graticule

There are multiple indicators on the grid:

Trigger Level Indicator shows the level where the
waveform triggers on the vertical axis.

Trigger Delay Indicator locates where the waveform
triggers on the horizontal axis.

When the trigger position is outside the screen, the
direction of the triangle changes to point outside the
screen.

Channel Offset Indicator with a channel number shows
the offset position of the corresponding channel.

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for LeCroy T3DSO2000A Series










































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands