manualshive.com logo in svg

Teledyne LeCroy T3DSO2000A Series, User Manual

Share
Download
Teledyne LeCroy T3DSO2000A Series User Manual Download Page 106

T3DSO2000A Manual. Page 102

•

Y1 — The upper (default) horizontal dotted line. It can be manually moved to any
vertical position on the screen.

•

Y2 — The lower (default) horizontal dotted line. It can be manually moved to any
vertical position on the screen.

•

Y1- Y2 — The difference between Y1 and Y2. After this option is selected, turn the
universal knob to move both Y1 and Y2 simultaneously.

X+Y (hori vertical) -- Both the X cursors and Y cursors are enabled.

Display Mode

Display Mode M1

Display Mode M2

•

M1 – The position information of each cursor is attached to the cursor, and the
difference information is between the two cursors with arrows connected to the
cursors. This mode is more intuitive.

•

M2 -- The position information of each cursor and the difference between the
cursors are displayed in a region on the screen. The region can be moved by
gestures to avoid covering the waveform. This mode is relatively concise.

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for LeCroy T3DSO2000A Series










































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands