Teledyne LeCroy T3DSO2000A Series User Manual Download Page 185

Page: 185 / 201

T3DSO2000A Manual. Page 181

29.3.1 File manager

The T3DSO2000A's file manager has similar style and operation with the Windows
operating systems.

A. Left window

B. Right window

C. Toolbar

D. Save/Recall command bar

E. Close the file manager

Left window:

Displays a list of available drives and internal folders.

•

The selected folder has an icon with a blue background.

•

The triangle tag on the left of the folder indicates that the folder includes
subfolder(s). Clicking the tag expands the folder to show the subfolder(s) in the left
window.

Right window:

Displays the files and the subfolders contained in the selected folder.

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for LeCroy T3DSO2000A Series










































































































































































































Search results

Summary of Contents for LeCroy T3DSO2000A Series

Reviews:

Brands by name

Popular brands

Teledyne LeCroy T3DSO2000A Series, User Manual

Search results

Summary of Contents for LeCroy T3DSO2000A Series

Reviews:

Brands by name

Popular brands