Teledyne LeCroy T3DSO2000A Series User Manual Download Page 115

Page: 115 / 201

•

Max: Highest value in the input waveform

•

Min: Lowest value in the input waveform

•

Pk-Pk: Difference between maximum and minimum data values

•

Top: Value of most probable higher state in a bimodal waveform

•

Base: Value of most probable lower state in a bimodal Waveform

•

Amplitude: Difference between top and base in a bimodal waveform. If not bimodal,
the difference between max and min

•

Mean: Average of data values

•

Cycle Mean: Average of data values in the first cycle

•

Stdev: Standard deviation of the data

•

Cycle Stdev: Standard deviation of the data in the first cycle

•

RMS: Root mean square of the data

•

Cycle RMS: Root mean square of the data in the first cycle

•

Median: Value at which 50% of the measurements are above and 50% are below

•

Cycle Median: Median of the first cycle

•

Overshoot (FOV): Overshoot following a falling edge; 100%* (base-min)/amplitude

•

Overshoot (ROV): Overshoot following a rising edge; 100%*(max-top)/amplitude

T3DSO2000A Manual. Page 111

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for LeCroy T3DSO2000A Series










































































































































































































Search results

Summary of Contents for LeCroy T3DSO2000A Series

Reviews:

Brands by name

Popular brands

Teledyne LeCroy T3DSO2000A Series, User Manual

Search results

Summary of Contents for LeCroy T3DSO2000A Series

Reviews:

Brands by name

Popular brands