Teledyne LeCroy T3DSO2000A Series User Manual Download Page 186

Page: 186 / 201

T3DSO2000A Manual. Page 182

Toolbar:

Graphical commands for file operations.

•

File Type: Specify the file type to display, including All (all types),
*.xml,*.ref,*.bmp,*.jpg,*.png,*.csv,*.dat,*.bin, *msk, *smsk

•

View Type: Contains two modes of "Detail" and "Icon”

Detail View Type

Icon View Type

•

Root Dir: Jump to root directory quickly

•

Up Level: Return to upper-level folder

•

Reload: Refresh file manager view

•

New Dir: Create a new folder under the current path

•

Rename: Rename the selected file or folder

•

Delete: Delete the selected file or folder

Save/Recall command bar

– Execute the Save/Recall command

•

Save As: Save as the filename specified by the user. Visible when the mode is
"Save"

•

Save: Save as system default file name. Visible when the mode is "Save"

•

Recall: Recall the specified file. Visible when the mode is "Recall"

29.3.2 External Save and Recall Instance

Save the screenshot to the path “Udisk0\t3dso2000a\” in the format of BMP

First, Insert the U disk.

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for LeCroy T3DSO2000A Series










































































































































































































Search results

Summary of Contents for LeCroy T3DSO2000A Series

Reviews:

Brands by name

Popular brands

Teledyne LeCroy T3DSO2000A Series, User Manual

Search results

Summary of Contents for LeCroy T3DSO2000A Series

Reviews:

Brands by name

Popular brands