manualshive.com logo in svg

Teledyne LeCroy T3DSO2000A Series, User Manual

Share
Download
Teledyne LeCroy T3DSO2000A Series User Manual Download Page 32

T3DSO2000A Manual. Page 28

9.7 Common Function

A. Press the button to turn on the search function and open the SEARCH dialog box.
Press again to turn off the search function.

B. Press the button to turn on navigate function and open the NAVIGATE dialog box.
Press again to turn off the navigate function

C. Press the button to turn on history function and open the HISTORY dialog box.
Press again to turn off the search function.

D. Press the button to turn on serial bus decode function and open the DECODE dialog
box. Press again to turn off the decode function.

9.8 Cursors Control

A. Push the button to open the cursors setup dialog box

B. Rotate the knob to move the selected cursor. Push to select a
different cursor.

9.9 Universal Knob

When the parameter setting area is highlighted, you can use the
Universal Knob to adjust or set the parameter. Press the knob to
select an option from the list. The default function of the Universal
Knob is to adjust the intensity of the waveform traces.

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for LeCroy T3DSO2000A Series










































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands