manualshive.com logo in svg

Teledyne LeCroy T3DSO2000A Series, User Manual

Share
Download
Teledyne LeCroy T3DSO2000A Series User Manual Download Page 146

T3DSO2000A Manual. Page 142

A. Mask area in green. Any dot violating the rule is highlighted in red, instead of the
normal waveform color.

B. Pass/Fail information display area, including the count of the passing frames, failed
frames, total frames, and the fail rate.

C. Dialog box

Perform Analysis> Mask Test to open the Mask Test dialog box:

A. Turn on/off the test

B. Select the source

（

C1~C4

）

C. Select the rule

（

All In, All Out, Any In and Any Out

）

D. Set the mask

E. Turn on/off the Pass/Fail operation. Turning off the operation

when the test is in progress will stop the test immediately,
and the counters in the information display area will stop.
Turn on the operation again re-starts the test and all the
counters are cleared. Pressing the Clear Sweeps button on
the front panel is equivalent.

F. Turn on/off the information display

G. Turn on/off “Stop on Fail”. When it is "on", the oscilloscope

stops the acquisition once it detects a failure

H. Turn on/off “Failure to History”. When it is "on", the failure

frame will be stored internally and can be viewed through
history function

I. Turn on/off “Capture on Fail”. When it is "on", the failure

waveform is detected, the screenshot with failure frame will
be stored in the external U disk.

J. Turn on/off the sound prompt when a failure occurs.

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for LeCroy T3DSO2000A Series










































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands