Calibration—475
h. CHECK—Repeat step 33-d.
i. ADJU ST—Channel 1's C36 and C37 (see Fig. 5-19)
with a low-capacitance screwdriver, for best corner and
flat-top waveform.
j. CAL A ID —Remove the 20 pF normalizer when
adjusting or checking the corner response.
k. IN T E R A C T IO N -B etw een Channel 1's C36 and C37.
Re-adjust both for optimum response.
I. Turn the CH 1 V O L T S /D IV switch to 20 m V.
m. CHECK—Repeat step 33-d.
n. ADJUST-Channel 1's C34 and C35 (see Fig. 5-19)
with a low-capacitance screwdriver, for best corner and
flat-top waveform.
o. IN T E R A C T IO N —Between Channel 1's C34 and C35.
Re-adjust both for optimum response.
p. Turn the CH 2 V O L T S /D IV switch to 50 mV.
q. CHECK—Repeat step 33-d.
r.
A DJUST-Channel 1's C32 and C33 (see Fig. 5-19)
with a low-capacitance screwdriver, for best corner and
flat-top waveform.
s. IN T E R A C T IO N —Between Channel 1's C32 and C33.
Re-adjust both for optimum response.
t. Turn the CH 1 V O L T S /D IV switch to 0.1 V.
u. CHECK—Repeat step 33-d.
v. Turn the CH 1 V O L T S /D IV switch to 0.2 V.
w. CHECK—Repeat step 33-d.
x. Turn the CH 1 V O L T S /D IV switch to 0.5 V.
y. C HECK —Repeat step 33-d.
z. A D JU ST—Channel 1's C30 and C31 (see Fig. 5-19)
with a low-capacitance screwdriver, for best corner and
flat-top waveform.
aa. IN T E R A C T IO N —Between Channel 1's C30 and C31.
Re-adjust both for optimum response.
ab. Repeat step 33-d for 1 V , 2 V , and 5 V positions of
the CH 1 V O L T S /D IV switch.
ac. Disconnect the test setup.
34. Check Vertical Amplifier Bandwidth
a. Connect the output of the High-Frequency Constant-
Amplitude Signal Generator (067-0532-01) to the CH 1
input via a GR-to-BNC adapter, X I 0 BNC attenuator, and a
50 12 BNC termination.
b.
Set the T R IG MODE switch to A U T O , the A
T IM E /D IV switch
to 0.2 ms, and both V O L T S /D IV
switches to 5 m V.
c. Adjust the High-Frequency signal generator output
amplitude for a five division display of a 3 megahertz
reference signal.
d. W ithout changing the output amplitude, increase the
output frequency of the High-Frequency signal generator
until the display is reduced to 3.5 divisions.
e.
C HECK —Output frequency of the High-Frequency
signal generator must be at least 200 megahertz.
f.
Move the test signal to the CH 2 input and set the
V E R T MODE switch to CH 2.
g. Repeat the bandwidth check procedure, step 34-c
through 34-e.
h. Disconnect the test setup.
35. Check Cascaded Bandwidth
a. Set both AC-GND-DC switches to DC, both V O L T S /
D IV switches to 5 m V , the A T IM E /D IV switch to 1 ms,
and the V E R T MODE switch to CH 1.
5-38
Summary of Contents for 475
