Calibration—475
Fjg. 5-25. Location of A and B Sweep timing adjustments.
j.
Note the reading on the D ELAY TIME POSITION dial
fo r use in step 68-k.
k.
Turn the D ELAY TIME POSITION dial 8 divisions
higher than the reading in step 68-j.
I.
CHECK—Time marker is at center vertical graticule
line.
m.
ADJUST—C1023 to position the time marker to the
center vertical graticule line.
n.
CAL A ID —Repeat the above procedure fo r optimum
tim ing response at +1.00 and +8.00 settings of the DELAY
TIME POSITION dial.
69. Adjust 0.1 Microsecond Timing
a.
Set the D ELAY TIM E POSITION dial to 1.00, the
HORIZ DISPLAY switch to A INTEN, and the B T IM E /
D IV switch to 0.1 Ms.
b.
Select 0.1
ms
time marks from the Time-Mark
Generator.
c.
CHECK—CRT display for 1 time marker/division,
w ithin 2% from +20°C to +30°C; 1 time marker/division,
w ithin 3% from —15°C to +55°C.
d.
ADJUST—C l025
(see
Fig. 5-25)
w ith
a
low-
capacitance screwdriver, fo r 1 time marker/division.
e.
Set the HORIZ DISPLAY switch to B D LY 'D and the
B T IM E /D IV switch to 0.01 Ms.
f.
Adjust the D ELAY TIM E POSITION dial to position
the tim e marker to the center vertical graticule line.
g.
Note the reading of the D ELAY TIM E POSITION dial
for use in step 69-h.
h.
Turn the D ELAY TIME POSITION dial 8 divisions
higher than the reading in step 69-g.
i.
CHECK—Time marker is at center vertical graticule
line.
j.
ADJUST—C l025 to position the time marker to the
center vertical graticule line.
k.
CAL A ID —Repeat the above procedure fo r optimum
tim ing response at +1.00 and +8.00 settings of the D ELAY
TIM E POSITION dial.
I.
Set the HORIZ DISPLAY switch to A and both
T IM E /D IV switches to 0.1
ms
.
m.
CHECK—CRT display for 1 time marker/division,
w ithin 1% from +20°C to +30°C; 1 time marker/division,
w ithin 3% from —15°C to +55°C.
n.
ADJUST—C l009
(see
Fig. 5-25)
w ith
a
low-
capacitance screwdriver for 1 tim e marker/division.
o. Disconnect the test setup.
70. Adjust Horizontal Output Centering
a.
Set the A T IM E /D IV switch to X-Y, the HORIZ
DISPLAY switch to A, and the VERT MODE switch to
CH 1.
5-52
Summary of Contents for 475
