Calibration—475
c. C HECK—That the CH 1 U N C A L light turns on when
the V A R control is out of the detent position.
d. C HECK —CRT display for 2 divisions or less of trace
shift when rotating the CH 1 V A R control through its
range.
e.
A D JU ST—CH 1 Variable Balance adjustment, R110
(see Fig. 5-8) for minimum trace shift when rotating the
CH 1 V A R control through its range.
f. Return the CH 1 V A R control to the detent position.
15. Adjust CH 1 Gain Switch Balance
a. Set the CH 1 V O L T S /D IV switch to 2 m V.
b. Position the trace to the center horizontal line.
c.
CHECK—CRT
display for minimum trace shift
between 2 m V and 5 m V positions of the CH 1 V O L T S /
D IV switch.
d.
A D JU ST—CH 1 Gain Switch Bal adjustment, R135
(see Fig. 5-8), for minimum trace shift between 2 mV and
5 m V positions of the CH 1 V O L T S /D IV switch.
16. Check Probe Indicator Lights
a. Set both V O L T S /D IV switches to 5 mV.
b. Connect a X I 0 probe to the CH 1 input.
c.
C HECK—Light under 5 m V setting is extinguished
and the light under 50 m V setting turns on.
Fig. 5-8. Location of CH 1 Var Voits/Div Balance and Gain Switch
Balance adjustments.
d. Set the V E R T MODE switch to CH 2.
e. Move the X I 0 probe to the CH 2 input.
f. CHECK—Light under 5 m V setting is extinguished and
the light under 50 m V setting turns on.
g. Remove the X I 0 probe.
17. Check AC-GND-DC Switches
a. Set both AC-GND-DC switches to DC.
b. Connect the Standard Amplitude Calibrator output to
the CH 2 input via a 42-inch 50 12 BNC cable.
c. Adjust the Standard Amplitude Calibrator for a
20 m V output.
d. Position the bottom of the display to the center
horizontal line.
e. Set CH 2 AC-GND-DC switch to GND.
f. C H E C K —For no vertical deflection, trace is at the
center horizontal line.
g. Set the CH 2 AC-GND-DC switch to AC.
h. CHECK —That the display is centered about the
center horizontal line.
i. Move the test signal to the CH 1 input.
j. Set the V E R T MODE switch to CH 1.
k. Position the bottom of the display to the center
horizontal line,
l
. Set the CH 1 AC-GND-DC switch to GND.
m. Repeat step 17-f.
n. Set the CH 1 AC-GND-DC switch to AC.
®
5 -3 0
Summary of Contents for 475
