C alib ratio n -475
2. Connect the autotransformer to a suitable power
source.
5. Set the controls as given under Preliminary Control
Settings (given prior to Part I —Performance Check). Allow
at least 20 minutes warmup before proceeding.
3. Connect the 475 to the autotransformer output.
N O T E
4. Set the auto transformer output voltage to the center
of the voltage range selected by the Line Voltage Selector.
Titles for external controls o f this instrument are
capitalized in this procedure (e.g., IN T E N S IT Y ).
Internal adjustments are initial capitalized only (e.g.,
C R T Grid Bias).
POWER SUPPLY C A LIB R A TIO N
Equipment Required
1. Precision DC Voltmeter
4. Three-inch Screwdriver
2. DC Voltmeter
3. Test Oscilloscope
5. Variable Auto-Transformer
Control Settings
Preset instrument controls to the settings given under
Preliminary Control Settings.
1- Check Power Supply DC Levels and Ripple
a.
Connect the Precision DC Voltmeter between test
point +50 V and GND (negative meter lead to ground) on
the main interface board. See Fig. 5-2.
c.
A D JU ST— +50 volt supply adjustment, R 1430, (see
Fig. 5-2) for a meter reading of +50 volts, within 0.1% or
50 m V.
d.
Using the Precision DC Voltmeter, measure the low
voltage power supplies given in Table 5-5. Observe proper
meter polarity. See Fig. 5-2 for test point locations.
b.
CHECK—Meter for a reading of +50 volts, within
0.5% or +250 mV.
Fig. 5-2. to w voltage power supply test points and +50 V adjust
ment.
e.
Using the Test Oscilloscope, check for correct ripple
as given in Table 5-5, while varying the autotransformer
between 103.5 VA C and 126.5 VAC .
TAB LE 5-5
Power Supply Tolerance and Ripple
Power Supply
Tolerance
Typical Ripple
(peak-to-peak)
+110 V
3% (3 .3 V )
1 V
+50 V
0.5% (250 m V)
2 m V
+15 V
1.5% (225 m V)
2 m V
+5 V
1.5% ( 75 m V)
2 m V
- 1 5 V
1.5% (225 m V)
2 m V
- 8 V
1.5% (120 m V)
2 m V
5-25
Summary of Contents for 475
