C alibration-475
34. Check Triggering
a. High-frequency triggering:
Internal
40 MH
200 MHz
AC
0.3 div
1.5 div
LF REJ
0.3 div
1.5 div
DC
0.3 div
1.5 div
External
AC
50 m V
250 m V
LF REJ
100 m V
500 m V
DC
50 m V
250 m V
Multiply by 10 for E X T -r 10 sensitivity.
H O R IZ O N T A L SYSTEM C A LIB R A TIO N
37. Adjust Delay Start and Delay Stop
a. A T IM E /D IV to 1 ms,
B T IM E /D IV to 5 jus,
H O R IZ D ISPLA Y to A IN T E N ,
B SOURCE to STARTS A FTE R D E L A Y ,
D E L A Y T IM E POSITION to 1.00.
b. Use 1 ms time markers.
c. A D JU ST—Delay Start, R938, to intensify the left side
b.
HF REJ—Triggers on 0.3 division at 50 kHz; does not
Qf the 2nd time marker,
trigger at 1 MHz.
c.
LF REJ—Triggers on 0.3 division at 50 kHz; does not
trigger on 60 Hz.
d.
Check SIN G L SWP operation and R EA DY light.
e.
Check A NORM triggering.
f.
Check LIN E triggering.
g.
Check A UTO recovery time.
35. Check External LEVEL Range
a. E X T : at least ±2 V (4 V P-P) for both A and B.
b. E X T -T- 10: at least ±20 V (40 V P-P) for A only.
36. Adjust T R IG V IE W
a.
A DJU ST—Trigger View Centering, R673, so trace is at
center horizontal line, within 1 division.
b.
Connect 200 mV square-wave signal from Standard
Amplitude Calibrator to A External Trigger input.
c.
Check for 3.2 to 4.8 divisions of display with T R IG
V IE W in.
d. D E L A Y T IM E POSITION to 9.00.
e. A D JU ST—Delay Stop, R936, to intensify the left side
of the 10th time marker.
f. H O R IZ D IS PLA Y to B D L Y 'D .
g. D E L A Y T IM E POSITION to 1.00.
h. A D JU ST—Delay Start, R938, so the 2nd time marker
starts at the beginning of the sweep.
i. D E L A Y T IM E POSITION to 9.00.
j. A D JU ST—Delay Stop, R936, so the 10th time marker
starts at the beginning of the sweep.
38. Check Differential Time Accuracy
a. Accuracy within 0.01 division from +15°C to + 3 5 °C.
b. Accuracy within 0.02 division from —1 5 °C to + 5 5 °C.
39. Adjust Horizontal Gain
a. H O R IZ D IS PLA Y to A,
both T IM E /D IV to 1 ms.
b. Use 1 ms time markers.
®
5-19
Summary of Contents for 475
