Calibration—475
c. Set the Test Oscilloscope T IM E /D IV switch so that
the bottom portion of the waveform (holdoff tim e o f the
+A GATE) is slightly less than one division.
d. Rotate the A TRIG HOLDOFF control clockwise
(not into the B ENDS A detent).
e. CHECK—For at least nine times increase in the
holdoff time of the +A GATE.
f. Set the A TRIG HOLDOFF control fu lly counter
clockwise.
C A LIB R A TO R , + GATES, AND
EXT Z-A XIS C A LIB R A TO R
Equipment Required
1. Medium-Frequency Constant-Amplitude Signal Genera-
4. BNC-T Connector
tor (Type 191)
2. Precision DC Voltmeter
3. GR-to-BNC Female Adapter
5. 42-inch 50 £2 BNC Cable (two)
6. Three-inch Screwdriver
Control Settings
Preset instrument controls to the settings given under
Preliminary Control Settings.
83. Adjust CALIB R A TO R Amplitude
a. Connect the Precision DC Voltmeter between the
CALIBRATOR current loop and ground.
b. Short the emitter and base o f Q1504 together (see
Fig. 5-32).
c. CHECK—For a meter reading of +0.3 volt, w ithin
3 mV.
d. ADJUST—Calibrator Am plitude adjustment, R1515
(see Fig. 5-32) for +0.3 volt, w ithin 1% from 0°C to +40°C;
for +0.3 volt, w ithin 1.5% from —15°C to +55°C.
Fig. 5-32. Location of Q 1504 and Calibrator amplitude adjustment.
e. Remove the Precision DC Voltm eter connections and
the short between emitter and base of Q1504.
84. Check A and B + GATE Outputs
a. Set the D ELAY TIM E POSITION dial fu lly counter
clockwise, the HORIZ DISPLAY switch to B D LY 'D , the B
SOURCE switch to STARTS AFTER D ELAY, the B
T IM E /D IV switch to 50
ms
, and the TRIG MODE to
AUTO.
b. Connect the B + GATE output signal to the Test
Oscilloscope via a 42-inch 50 12 BNC cable.
c. CHECK—Test Oscilloscope for a positive-going pulse
+5.5 volts in amplitude (within 0.5 V).
d. Remove the B + GATE output signal and connect the
A + GATE output signal to the Test Oscilloscope.
e. CHECK—Repeat step 84-c.
f. Disconnect the test setup.
85. Check EXT Z-A XIS Operation
a. Set the HORIZ DISPLAY switch to A, the A
T IM E /D IV switch to 0.2 ms, and the A SOURCE switch to
NORM.
®
5-59
Summary of Contents for 475
