Calibration—475
4.
Check Channel 2 Inverted Balance
a.
Set the V E R T MODE switch to CH 2 and the CH 2
AC-GND-DC switch to GND.
b.
Position the trace to the center horizontal line with
the CH 2 POSITION control.
c.
Push the IN V E R T switch.
d.
CHECK—Trace does not vertically shift more than 1
division between the positions of the IN V E R T switch.
5. Check Channel 1 and 2 Position Range
a.
Connect the Standard Amplitude Calibrator output
to the CH 1 and CH 2 inputs via a 42-inch 50 12 BNC cable
and a dual input coupler.
b.
Set both V O L T S /D IV switches to 2 m V and both
AC-GND-DC switches to AC.
c. Adjust the Standard Amplitude Calibrator for a
50 m V output.
d. CHECK—That the top of the CRT display can be
positioned below the center horizontal line, and the bottom
of the display can be positioned above the center hori
zontal line.
e. Set the V E R T MODE switch to CH 1.
f.
CHECK—That the top of the CRT display can be
positioned below the center horizontal line, and the bottom
of the display can be positioned above the center horizontal
line.
6. Check Channel 1 and 2 Gain
a. Set both V O L T S /D IV switches to 5.mV.
b.
Adjust the Standard Amplitude Calibrator for a
20 m V square-wave output.
c.
CHECK —CRT display for 4 divisions of deflection,
within 0.12 division.
d.
Set the V E R T MODE switch to CH 2.
e.
CHECK—CRT display for 4 divisions of deflection,
within 0.12 division.
7.
Check Add Mode Operation
a.
Set both AC-GND-DC switches to DC.
b.
Adjust the Standard Amplitude Calibrator for a
10 m V output.
c. Set the V E R T MODE switch to A D D .
d.
CHECK —C RT display for 4 divisions, within 0.12
division, of amplitude.
8. Check Channel 1 and 2 Deflection Accuracy
a.
Set the V E R T MODE switch to CH 1 and the CH 2
AC-GND-DC switch to GND.
b.
C HECK —Using the CH 1 V O L T S /D IV switch and the
Standard Amplitude Calibrator settings given in Table 5-2,
check that the vertical deflection factor is within the given
tolerance in each position of the CH 1 V O L T S /D IV switch.
TAB LE 5-2
Vertical Deflection Accuracy
V O L T S /
Standard
Vertical
Maximum
D IV
Amplitude
Deflection
Error
Switch
Calibrator
in
for 3%
Setting
Output
Divisions
Accuracy
2 m V
10 m V
5
Previously
set
5 m V
20 m V
4
Previously
set
10 m V
50 m V
5
±0.15 div
20 m V
0.1 V
5
± 0.15 div
50 m V
0.2 V
4
± 0.12 div
0.1 V
0.5 V
5
±0.15 div
0.2 V
1 V
5
± 0.15 div
0.5 V
2 V
4
± 0.12 div
1 V
5 V
5
± 0.15 div
2 V
10 V
5
± 0.15 div
5 V
20 V
4
± 0.12 div
c.
Set the V E R T MODE switch to CH 2.
d.
Set the CH 1 AC-GND-DC switch to GND and the
CH 2 AC-GND-DC switch to DC.
5-7
Summary of Contents for 475
