Calibration—475
f.
C HECK—For LOW LIN E indicator light to turn on
when the autotransformer is below 103 volts.
g. Return the autotransformer for a 115 VAC output.
2.
Check High Voltage Power Supply
a.
Connect the DC Voltmeter between the -2 4 5 0 -v o lt
test point and ground (positive meter lead to ground). See
Fig. 5-3.
b.
CHECK—Meter for a reading of —2450 volts, within
±49 volts.
Fig. 5-3. Location of high-voltage and Grid Bias test points and
adjustments.
DISPLAY and Z-A XIS C A LIB R A TIO N
Equipment Required
1. DC Voltmeter
5. 42-inch 50 £2 BNC Cable
2. Time-Mark Generator (Type 2901)
6. 50 £2 BNC Termination
3. Test Oscilloscope
7. Three-inch Screwdriver
4. X I 0 Probe
8. Low-Capacitance Screwdriver
Control Settings
Preset instrument controls to the settings given under
Preliminary Control Settings except as follows:
IN T E N S IT Y
Fully Counterclockwise
T R IG MODE
NORM
3. Adjust CRT Grid Bias
a.
Connect the DC Voltmeter between TP1364 and
ground. (Negative meter lead to ground.) See Fig. 5-3.
b.
Set the IN T E N S IT Y control for a meter reading of
+15 volts.
c.
C HECK—CRT display for the dimmest, well-defined
dot.
d.
A D JU ST—CRT Grid Bias adjustment, R1375 (see
Fig. 5-3) for dimmest, visible dot.
e.
Turn CH 1 POSITIO N , FOCUS, and IN T E N S IT Y
controls fully clockwise.
f.
C HECK —Meter reading is between +20 volts and +30
volts.
g. Push BEAM F IN D pushbutton.
h.
C HECK—Meter for a reading of approximately +25
volts.
i.
Release BEAM F IN D button and remove DC V olt
meter connections.
j. Turn FOCUS, IN T E N S IT Y , and CH 1 POSITION
controls to mid-range.
k. Adjust FOCUS and IN T E N S IT Y controls for a
well-defined dot of nominal intensity.
5-26
Summary of Contents for 475
