Calibration—475
b. Connect the CH 2 V E R T S IG N A L O U T (on the rear
panel) to the CH 1 input via a 42-inch 50 £2 BNC cable and
a 50 12 BNC termination.
c. Connect
the
output of the Medium-Frequency
Constant-Amplitude Signal Generator (Type 191) to the
CH 2 input via a GR-to-BNC adapter, 42-inch 50 12 BNC
cable, X I 0 BNC attenuator, and a 50 12 BNC termination.
d. Adjust the Medium-Frequency signal generator for a
five division display of a 50 kHz signal.
e.
Without changing the output amplitude of the
Medium-Frequency signal generator, increase the output
frequency until the display is reduced to 3.5 divisions.
f.
CHECK—Output frequency of the Medium-Frequency
signal generator must be at least 50 megahertz.
g.
Disconnect the test setup from the CH 2 V E R T
S IG N A L O U T to the CH 1 input connector.
36. Check Vertical Channel Isolation
a. Set the V E R T MODE switch to CH 2, the CH 2
V O L T S /D IV switch to 0.2 V , and the CH 1 AC-GND-DC
switch to GND.
b. Connect
the output of the
Medium-Frequency
Constant-Amplitude Signal Generator (Type 191) to the
CH 1 & 2 inputs via a GR-to-BNC adapter, 42-inch 50 12
BNC cable, X I 0 BNC attenuator, 50 12 BNC termination,
and a dual input coupler.
c.
Adjust the Medium-Frequency signal generator for a 4
division display of a 50 MHz signal.
d.
Set both V O L T S /D IV switches to 20 m V and the
V E R T MODE switch to CH 1.
e.
CHECK —CRT display for no more than 0.2 division
of deflection.
f.
Set the CH 2 AC-GND-DC switch to G N D , the CH 1
AC-GND-DC switch to DC, and the CH 1 V O L T S /D IV
switch to 0.2 V .
g.
Adjust the Medium-Frequency signal generator for a 4
division display of a 50 MHz signal.
h. Set the V E R T MODE switch to CH 2.
i.
C HECK —C RT display for no more than 0.2 division of
deflection.
j.
Disconnect the test setup.
37. Check Bandwidth Lim it Operation
a. Pull the 20 MHz BW /TRIG VIEW button to BW and
set the CH 1 AC-GND-DC switch to DC.
b. Connect the Medium-Frequency Constant-Amplitude
Signal Generator (Type 191) to the C H I input via a
42-inch 50 12 BNC cable and a 50 12 BNC termination.
c.
Adjust the Medium-Frequency signal generator for a
six division display of a 50 kilohertz signal.
d.
Increase the output frequency of the signal generator
until the display is reduced to 4.2 divisions.
e.
C HECK —Output frequency of the signal generator is
between 15 and 25 megahertz.
f.
Disconnect the test setup.
5-39
Summary of Contents for 475
