C alibration-475
c.
A DJU ST—Horizontal
Gain,
R1155, for 1
time
marker/division, within 1%, from +20°C to +30°C; for 1
time marker/division, within 3%, from —15°C to +55° C.
d.
Use 0.1 ms time markers.
e.
Push X 10 MAG in.
f.
Check that the X I 0 MAG light is on.
g.
Check for 1 time marker/division, within 2%, from
+20°C to +30°C; for 1 time marker/division, within 4%,
from —15°C to +55° C.
40. Adjust Magnifier Registration
a.
Use 5 ms time markers.
b.
A DJU ST—Magnifier Registration, R1130, to position
the second time marker to the center vertical line, within
0.4 division, between positions of X I 0 MAG switch.
41. Check V A R T IM E /D IV Range
a. A T IM E /D IV to 2 ms.
b. Use 5 ms time markers.
c.
Check for 1 time marker/division by rotating the
V A R T IM E /D IV control.
d. Check U NC AL light.
42. Check Horizontal POSITION Control Range
43. Adjust 10 jits Timing
a.
Both T IM E /D IV to 10
ms
.
b. Use 10
ms
time markers.
c.
A D JU ST—C l 064 for 1 time marker/division, within
1%, from +20°C to +30°C; 1 time marker/division, within
3%, from - 1 5°C to +55° C.
d. H O R IZ D IS PLA Y to A IN T E N ,
B T IM E /D IV to 0.01 Ms.
e.
A D JU ST—C l 023 for 1 time marker/division, within
1%, from + 2 0 ° C to +30°C; 1 time marker/division, within
3%, from - 1 5°C to +55° C.
44. Adjust 0.1
ms
Timing
a. D E L A Y T IM E POSITION to 1.00,
H O R IZ D IS PLA Y to A IN T E N ,
B T IM E /D IV to 0.1 Ms.
b. Use 0.1 Ms time markers.
c. A D JU ST—C l 025 for 1 time marker/division, within
2%, from +20°C to +30°C; 1 time marker/division, within
3%, from —15°C to +55° C.
d. H O R IZ D IS PLA Y to A,
both T IM E /D IV to 0.1 Ms.
e.
A D JU S T—C l009 for 1 time marker/division, within
1%, from +20°C to +30°C; 1 time marker/division, within
3%, from - 1 5°C to +55° C.
45. Adjust Horizontal Output Centering
a. A T IM E /D IV to X -Y ,
H O R IZ D ISPLA Y to A.
b. Horizontally center the dot.
c.
Adjust the CH 1 POSITION until the voltage on the
collector of Q1214 equals that on the collector of Q1204.
d.
A D JU ST—Horizontal Output Center, R1256, for
+50 V on the collectors of Q 1214 and Q1204.
46. Adjust High Speed Timing-Visual Method
a.
A T IM E /D IV to 0.05
ms
,
X I 0 MAG pushed in,
A SOURCE to E X T ,
A CO U PLIN G to LF REJ.
5-20
Summary of Contents for 475
