4. Check ASTIG Control
a.
Rotate ASTIG control (front panel screwdriver adjust
ment) through its range.
b.
CHECK—For dot de-focus at both extremes of the
A STIG control.
c. Reset the ASTIG control for a well-defined dot.
5.
Check Display Controls
a. Rotate SCALE IL L U M control through its range.
b. CHECK—For a smooth increase in illumination.
c. Set the IN T E N S IT Y control to mid-range.
d. Rotate the FOCUS control through its range.
e. CHECK—For trace de-focus at both extremes of the
FOCUS control.
f.
Rotate the IN T E N S IT Y control from fully counter
clockwise to fully clockwise.
g.
CHECK—For trace intensity to increase smoothly
from minimum to maximum intensity.
h.
Reset the IN T E N S IT Y and FOCUS controls for a
well-defined trace.
6. Adjust Trace Alignment
a.
Position the trace to the center horizontal graticule
line.
b.
C HECK—That the trace is parallel with the center
horizontal line.
c.
A D J U S T -T R A C E
R O T A T IO N adjustment (front
panel adjustment) to make the trace parallel to the center
horizontal line.
7. Adjust Y Axis Alignment
a.
Connect 0.1 ms time marks from the Time-Mark
Generator (Type 2901) to the CH 1 input via a 42-inch
50 £2 BNC cable and a 50 12 BNC termination.
Calibration—475
b.
Set the CH 1 AC-GND-DC switch to DC and the CH 1
V O L T S /D IV switch to 0.1 V.
c. Adjust the A LE V E L control for a stable display, the
A STIG and FOCUS controls for a well-defined display.
d. Adjust the VAR T IM E /D IV control for 1 time
marker/division.
e.
C HECK —For no more than 0.1 division of tilt of the
center time marker as compared with the center vertical
graticule line.
f.
A D JU ST—Y Axis Alignment adjustment, R1385, (see
Fig. 5-4) to align the center time marker with the center
vertical line.
g.
IN T E R A C T IO N —Between Y Axis Alignment and
T R A C E R O TA TIO N adjustments. Adjust both for total
optimum response.
8.
Adjust Geometry
a. C HECK —CRT display for no more than 0.1 division
vertical curvature of the time markers across the viewing
area.
b. A D J U S T —G eom etry
adjustment,
R1390
(see
Fig. 5-4) for minimum curvature of the time markers across
the viewing area.
c. Remove the test signal from CH 1 input.
d.
CHECK—For no more than 0.1 division of curvature
of the trace when positioned from top to bottom of the
graticule area.
Fig. 5-4. Location of Y-Axis Align, Z-Axis, and Geometry adjust
ments and test point.
5-27
Summary of Contents for 475
