Calibration—475
g. Rotate the CH 1 V A R control fully counterclockwise.
h. CHECK—C RT display reduces to less than 2 divisions.
i.
Return the VA R controls to the detent position.
26. Check A DD Mode Operation
a.
Set both V O L T S /D IV switches to 5 m V and both
AC-GND-DC switches to DC.
b. Connect the Standard Amplitude Calibrator output to
both channel inputs via a dual input coupler.
c.
Adjust the Standard Amplitude Calibrator for a
10 m V output.
d. Set the V E R T MODE switch to A D D .
e.
CHECK —For 4 divisions of deflection, within 0.12
division.
27. Check Compression and Expansion
a.
Set the CH 2 AC-GND-DC switch to GND and the
VE RT MOD E switch to CH 1.
b. Adjust the CH 1 V A R control for 2 divisions of
deflection centered about the center horizontal line.
c.
Position the top of the display to the top graticule
line.
d. CHECK —C RT display for 0.1 division or less of
compression or expansion.
e. Position the bottom of the display to the bottom
graticule line.
f. C HECK —CRT display for 0.1 division or less of
compression or expansion.
g. Return the CH 1 VAR control to the detent position.
h. Disconnect the test setup.
5-34
28. Check A L T Mode Operation
a. Set the V E R T MODE switch to A L T and the A
L E V E L control fully clockwise.
b. Position the two traces 2 divisions apart.
c.
C HECK —That the sweeps alternate at all settings of
the A T IM E /D IV switch, except X -Y .
29. Check CHOP Mode Operation
a.
Set the A T IM E /D IV switch to 0.2
m s
,
the A SOURCE
switch to N O R M , the A SLOPE switch to +, the V E R T
MODE switch to CHOP, and both AC-GND-DC switches to
GND.
b. Position the two traces 4 divisions apart.
c. Adjust the A LE V E L control for a stable display.
d.
C H E C K —For
complete
blanking
of
switching
transients between chopped segments (see Fig. 5-15).
e.
CHECK —Duration of each cycle is about 5 divisions.
30. Adjust
Vertical
Output
Amplifier
High-
Frequency Response
a.
Set the V E R T MODE switch to CH 1.
Fig 5-15. Typical CRT display when checking chopped blanking.
Summary of Contents for 475
