Calibration—475
Fig. 5-22. Location of Trigger View Centering adjustment.
61. Check Trigger View Deflection Factor
a. Connect the output of the Standard Amplitude
Calibrator to the A External Trigger input via a 42-inch
50 £2 BNC cable.
b. Adjust the Standard Amplitude Calibrator for a
200 m V output.
c. Push the T R IG V IE W button and hold it in.
d. CHECK—For 3.2 to 4.8 divisions of display.
e. Release the T R IG VIEW button.
f. Disconnect the test setup.
H O R IZ O N T A L SYSTEM C A LIB R A TIO N
Equipment Required
1. Standard Amplitude Calibrator (067-0502-01)
6. P6022 Current Probe
2. Medium-Frequency Constant-Amplitude Signal Genera
tor (Type 191)
7. 42-inch 50 £2 BNC Cable (two)
8. 50 £2 BNC Termination (two)
3. Time-Mark Generator (Type 2901)
9. Dual Input Coupler
4. Test Oscilloscope
10. Three-inch Screwdriver
5. X I 0 Probe
11. Low-Capacitance Screwdriver
Control Settings
Preset instrument controls to the settings given under
Preliminary Control Settings except as follows:
c. A D J U S T —Delay
Start
adjustment,
R938
(see
Fig. 5-23), so the left side of the intensified zone starts on
the leading edge of the second time marker.
A T IM E /D IV
B T IM E /D IV
H O R IZ DISPLAY
BSO URCE
D E L A Y T IM E POSITION
1 ms
1 jus
A INTEN
STARTS A FTE R D E L A Y
1.00
62. Adjust Delay Start and Delay Stop
a.
Connect 1 ms time marks to the CH 1 input from the
Time-Mark Generator (Type 2901) via a 42-inch 50 £2 BNC
cable and a 50 £2 BNC termination.
d. Set the D E L A Y T IM E POSITION dial to 9.00.
b.
CHECK—Intensified portion of the sweep begins at
the second time marker.
Fig. 5-23. Location of Delay Start and Delay Stop adjustments.
5-49
Summary of Contents for 475
