Calibration—475
g. Set the V E R T MODE switch to CH 1.
h. CHECK—Repeat step 50-b.
i. Set the A SOURCE switch to NORM.
j. CHECK—Repeat step 50-b.
k. Set the A SOURCE switch to CH 2.
I. CHECK—Repeat step 50-f.
m. Disconnect the test setup.
51. Check HF RE J Triggering
a. Set the H O R IZ D ISPLA Y switch to A f the T IM E /D IV
switches to 2 /is, the T R IG MODE switch to A U TO , both
COUPLING switches to HF REJ, and both SOURCE
switches to NORM.
b. Connect
the output of the
Medium-Frequency
Constant-Amplitude Signal Generator (Type 191) to the
CH 1 input via a 50 12 5 ns GR cable, a 50 12 Signal Pickoff
Unit (Type CT-3), a GR-to-BNC adapter, and an 18-inch
50 12 BNC cable.
c. Connect the 10% output of the Signal Pickoff Unit to
the A External Trigger input via an 18-inch 50 12 BNC cable
and a 50 12 BNC termination.
d. Adjust the Medium-Frequency signal generator for a
0.5 volt, 50 kilohertz, output signal.
e. Adjust the CH 1 V O L T S /D IV switch for a 0.3 division
display.
f. C HECK—That a stable display can be obtained on
both slopes of the displayed waveform in all positions of
the A COUPLING switch, by adjusting the A LEVEL
control.
g. Increase the output of the Medium-Frequency signal
generator to 1 megahertz.
h. CHECK—That a stable display cannot be obtained in
the HF REJ position of the A COUPLING switch.
i. Set the A SOURCE switch to E XT.
j. C HECK—That a stable display cannot be obtained in
the HF REJ position of the A COUPLING switch.
k. Reduce
the
Medium-Frequency signal generator
output frequency to 50 kilohertz.
I. CHECK —That a stable display can be obtained on
both slopes of the displayed waveform, in all positions of
the A COUPLING switch, by adjusting the A LEV E L
control.
m. Move the external Trigger signal to the B External
Trigger input.
n. Set the H O R IZ DISPLAY switch to B D L Y 'D .
o. CHECK —That a stable display can be obtained on
both slopes of the displayed waveform, in all positions of
the
B COUPLING switch, by adjusting the LEV E L
controls.
p. Increase the output of the Medium-Frequency signal
generator to 1 megahertz.
q. CHECK —That a stable display cannot be obtained in
the HF REJ position of the B COUPLING switch.
r. Set the B SOURCE switch to E XT.
s. CHECK —That a stable display cannot be obtained in
the HF REJ position of the B COUPLING switch.
t. Reduce the Medium-Frequency signal generator out
put frequency to 50 kilohertz.
u. CHECK —That a stable display can be obtained on
both slopes of the displayed waveform, in all positions of
the B COUPLING switch, by adjusting the LEV E L
controls.
v. Disconnect the test setup.
5-45
Summary of Contents for 475
