Calibration—475
TAB LE 5-1 (cont)
Description
Minimum
Specifications
Usage
Examples
20. Attenuator (two re
quired)1
Attenuation ratio, X 10; con
nectors, GR; impedance, 50
ohms.
Vertical system frequency re
sponse adjustments.
a. Tektronix Part Number
017-0078-00.
21. Attenuator1
Attenuation ratio, X 5; con
nectors, GR; impedance, 50
ohms.
Vertical system frequency re
sponse adjustments.
a. Tektronix Part Number
017-0079-00.
22. Termination (two re
quired)
Impedance, 50 ohms; accu
racy, within 3%; connectors,
BNC.
Vertical amplifier bandwidth
check; trigger circuit opera
tion checks and adjustments.
a. Tektronix Part Number
011-0049-01.
23. T-Connector1
Connectors, BNC.
Used
for
signal
inter
connection.
a. Tektronix Part Number
103-0030-00.
24. Input Normalizer1
RC time constant, 20 pico
farads times 1 megohm.
Standardize input RC time
constant.
a. Tektronix Part Number
067-0538-00.
25.
Dual-Input
Coupler
(two required)
Connectors, BNC; matched
signal transfer to each input.
Used
fo r
signal
in te r
connection.
a. Tektronix calibration fix-
t u r e
P a r t
N u m b e r
067-0525-00.
26. Screwdriver1
Three-inch shaft; 3/32-inch
bit.
Used throughout procedure
to adjust variable resistors.
a. Tektronix Part Number
003-0192-00.
2 7 .
L o w -C a p a c ita n c e
Screwdriver1
1 1/2-inch shaft.
Used throughout procedure
to adjust variable capacitors.
a. Tektronix Part Number
003-0000-00.
P R E L IM IN A R Y CONTROL SETTINGS
Preset the instrument controls to the settings given
below when starting a Performance Check or a Calibration
procedure.
Power Controls
POWER
ON
CRT Controls
IN T E N S IT Y
FOCUS
SCALE IL L U M
BEAM F IN D
Midrange
Midrange
Midrange
O ff (button out)
Vertical Controls (both Channels if applicable)
V O L T S /D IV
VA R
POSITION
AC-GND-DC
5 m V
Calibrated detent
Midrange
DC
V E R T MODE
IN V E R T
20 MHz BW (PULL)
CH 1
O ff (button out)
O ff
Triggering Controls (both A and B if applicable)
L E V E L
SLOPE
COUPLING
SOURCE
T R IG MODE
Fully clockwise
+
AC
NORM
A UTO
Sweep Controls
H O R IZ D IS PLA Y
D E L A Y T IM E POSITION
A T IM E /D IV
B T IM E /D IV
V A R
X I 0 MAG
POSITION
FIN E
A T R IG H O LD O FF
A
Fully counterclockwise
1 ms
1 ms
Calibrated detent
O ff (button out)
Midrange
Midrange
NORM
5-4
Summary of Contents for 475
