Calibration—475
g. Repeat the bandwidth check procedure, step 12-c
through 12-e.
CH 2 input via a GR-to-BNC adapter, 42-inch 50 £2 BNC
cable, X I 0 BNC attenuator, and a 50 £2 BNC termination.
h. Disconnect the test.se.tuiL
13. Check Cascaded Bandwidth
d. Adjust the Medium-Frequency signal generator for a
five-division display of a 50 kilohertz signal.
a. Set both AC-GND-DC switches to DC, the A T IM E /
D IV switch to 1 ms, and the V E R T MODE switch to CH 1.
e. W ithout changing the output amplitude of the signal
generator, increase the output frequency until the display is
reduced to 3.5 divisions.
b. Connect the CH 2 V E R T S IG N A L O U T (on the rear
panel) to the CH 1 input via a 42-inch 50 £2 BNC cable and
a 50 £2 BNC termination.
f . C H E C K —O u tp u t
frequency
of
the
Medium-
Frequency signal generator must be at least 50 megahertz.
c. Connect the output of the Medium-Frequency
Constant-Amplitude Signal Generator (Type 191) to the
g. Disconnect the test setup.
TR IG G ER SYSTEM CHECK
Equipment Required
1. Standard Amplitude Calibrator (067-0502-01).
6.
42-inch
50
f t BNC Cable.
2. M e d iu m -F re q u e n c y
Constant-Am plitude
Signal
Generator (Type 191).
7.
18-inch
50
f t BNC Cable.
A
X# *fl A A It 1
A A . .
8. X I 0 BNC Attenuator.
3. 50 £2 Signal Pickoff Unit (Type CT-3).
9. X 2 BNC Attenuator.
4. 50 £2 5 nanosecond GR Cable.
10. 50 £2 BNC Termination (two).
5. GR-to-BNC female Adapter.
11.
Dual Input Coupler (two).
Control Settings
Preset instrument controls to the settings given under
Preliminary Control Settings except as follows:
18-inch 50 £2 BNC cable, a 50 £2 BNC termination, and a
dual input coupler.
both T IM E /D IV
0.05
fJ is
c. Adjust the Medium-Frequency signal generator to
maintain a 0.3-division display of a 50 kilohertz signal.
14. Check A Triggering
d. Rotate the A SLOPE switch between
+
and —.
a. Connect the output of the Medium-Frequency
Constant-Amplitude Signal Generator (Type 191) to the A
External Trigger input via a 50 £2 5 ns GR cable, 50 £2
Signal Pickoff Unit (Type CT-3) thru output, GR-to-BNC
adapter, X I 0 BNC attenuator, X 2 BNC attenuator, 50 £2
BNC termination, and a dual input coupler.
e. CHECK —A stable display can be obtained on both
slopes of the displayed waveform in all positions of the A
COUPLING switch by adjusting the A LEV E L control.
b. Connect the 10% BNC output connector of the 50 £2
Signal Pickoff Unit to the CH 1 and CH 2 inputs via an
f. Set the A SOURCE switch to CH 1.
g. C HECK —Repeat steps 14-d and 14-e.
®
5-9
g. C HECK —Repeat steps 14-d and 14-e.
Summary of Contents for 475
