PART I I —SHORT-FORM C A LIB R A TIO N
Calibration—475
Introduction
The following procedure is intended to be used as
guidelines for calibration of the 4 75 by experienced
technicians familiar with the instrument. Only essential
information is given. Test Equipment Required is the same
as that given for Part I I I —Calibration.
Preliminary Procedure for Short-Form Calibration
N O T E
This instrument shou/d be adjusted a t an ambient
tem perature o f
+ 2 5 °C (±5°C ) for best overall
accuracy.
1. Remove the dust cover from the 475.
2. Connect the 475 to the autotransformer and set the
line voltage to 115 VAC .
3. Set the controls as given under Preliminary Control
Settings (given prior to Part I —Performance Check). Allow
at least 20 minutes warmup before proceeding.
N O T E
Titles for external controls o f this instrument are
capitalized in this procedure (e.g., IN T E N S IT Y ).
Internal adjustments are initial capitalized only (e.g..
Grid Bias).
POWER SUPPLIES and
D ISPLAY C A LIB R A TIO N
1. Low Voltage Power Supplies
a. A D J U S T - +50 V supply, R1430, ±0.5%.
b. Check— +110 V supply, ±3%.
c. Check— +15 V supply, ±1.5%.
d. Check— +5 V supply, ±1.5%.
e. Check----- 15 V supply, ±1.5%.
f . Check----- 8 V supply, ±1.5%.
g. Check ripple on supplies (except + 1 1 0 V supply) is
2 m V P-P maximum; + 1 1 0 V supply ripple is I V P-P
maximum.
h. Check regulation between 126.5 V and 103.5 V line.
i. Check
LOW
LIN E
indicator
comes
on
below
103 VAC.
2. High Voltage Power Supply
—2450 volts, ±4 9 volts.
3. Adjust CRT Grid Bias
a. T R IG MODE to NORM.
b. Connect DC Voltmeter to TP1364 and adjust IN T E N
S IT Y for a reading of +15 volts.
c. A D JU S T—CRT Grid Bias, R1375, for dimmest dot.
4. Check Display Controls
a. A STIG
b. SCALE IL L U M
c. FOCUS
d. IN T E N S IT Y
5. Adjust Trace Alignment
a. Connect time markers to CH 1 input.
b. A D JU S T—TRACE R O T A T IO N to align trace with
center horizontal line.
c. A D JU ST—Y Axis Alignment, R1385, to align center
time marker with the center vertical line.
5-14
d. Check for no more than 0.1 division curvature.
Summary of Contents for 475
