419050/B
151
the transducer surface will allow water to penetrate the transducer. If a leak occurs,
the transducer must be replaced.
• The top mating surface of the installation trunk must be protected with a wooden
cover at all times until the hull unit is installed. It is very important that this surface
is clean and undamaged, because it must be watertight after the hull unit has been
installed on top of the installation trunk.
• The Motor Control Unit must never be physically dismounted from the hull unit gantry.
A dedicated gasket (O-ring) is provided with the hull unit. This gasket ensures a
watertight connection between the installation trunk and the bottom of the transducer
shaft sleeve. During the installation process, make sure that this gasket is kept safe from
damage, and that the top of the installation trunk is kept clean, smooth and without
physical damage such as scratches or dents. Proper O-ring lubrication must be applied
before the hull unit is mounted on top of the installation trunk and gasket.
Procedure
1
Lift the hull unit (
with the transducer protection still in place!
) and place it
vertically over the installation trunk
2
While lifting, make sure that you do not damage the delicate parts of the hull unit.
Note
Make sure that you keep the transducer safe, and the transducer cable and
connector dry. Watch these carefully to prevent these delicate parts from being
damaged, stuck or hooked on to protruding objects while manoeuvring the hull unit
into the sonar room. Do not remove the transducer protection (the thick foam) until
just before the hull unit is lowered onto the installation trunk.
3
Remove the wooden protective cover from the top of the installation trunk.
Store the protective cover in the sonar room for possible future use.
4
Check the top of the installation trunk. Verify that:
a
Make sure that the rubber gasket on the top of the installation trunk is not
damaged.
b
Make sure that the surface of the installation trunk is clean and free from grit
or other damaging particles.
c
Make sure that the top of the installation trunk has not been damaged, and that
it is smooth and even without physical scratches or dents.
5
Apply O-ring silicone grease.
6
Remove the transducer protection.
7
Lower the hull unit carefully onto the installation trunk.
Summary of Contents for SC90
