Siemens SIMOTRAS 6SG7050, Operating Instructions Manual

Page: 370 / 604

Parameter list 01.04
11-22
SIEMENS AG 6SG7000-0BA76
SIMOTRAS HD Operating Instructions
PNU Description Value range
[Unit] No. indices See
Change
P159
FDS
(G163)
Switchover threshold for auto-reversing stage
P159 P159
Required
torque direction
Speed controller
output
I
0
II
0.00 to 100.00
[%]
0.01% of n controller
output Ind: 4
FS=5.00
Type: O2 P052 = 3
P051 = 40
Online
P160
FDS
(G163)
Additional torque-free interval
Additional torque-free interval for torque direction change in 4Q operation.
0.000 to 2.000
[s]
0.001s Ind: 4
FS=0.000
Type: O2 P052 = 3
P051 = 40
Online
P164
*
FDS
(G162)
Set current controller P component to zero
0 Set controller P component to zero (i.e. to obtain pure I
controller)
1 Controller P component is active
0 to 1
1 Ind: 4
FS=1
Type: O2 P052 = 3
P051 = 40
Offline
P166
FDS
(G162)
Filter time for precontrol
The precontrol input signal is applied via a filtering element
0 to 10000
[ms]
Ind: 4
FS=40
Type: O2 P052 = 3
P051 = 40
Online
P167
FDS
(G162)
Maximum firing angle
With P153 = 2 and if no “zero delay-angle setting“, the output of the
precontrol is limited to P167.
0 to 165
[°]
Ind: 4
FS=45
Type: O2 P052 = 3
P051 = 40
Online
P168
FDS
(G163)
Maximum change to firing angle
The change of the firing angle from one firing instant to the next is limited.
1 to 179
[°]
Ind: 4
FS=15
Type: O2 P052 = 3
P051 = 40
Online
11.10 Current limitation, torque limitation
P171
FDS
(G160)
(G161)
System current limit in torque direction I 0.0 to 300.0
[% of P100]
0.1% of P100 Ind: 4
FS=200.0
Type: O2 P052 = 3
P051 = 40
Online
P172
FDS
(G160)
(G161)
System current limit in torque direction II -300.0 to 0.0
[% of P100]
0.1% of P100 Ind: 4
FS=-200.0
Type: I2 P052 = 3
P051 = 40
Online
P174
*
(G161)
(G163)
Control word root generator [SW 2.1 and later]
0 Root generator not active
recommended for current-controlled operation (P084=2)
1 Root generator active
0 to 1
1 Ind: None
FS=1
Type: O2 P052 = 3
P051 = 40
Online
P175
*
FDS
(G162)
Source for variable P gain [SW 1.8 and later]
The content of the selected connector acts as the P gain for the current
controller after multiplication with P155.
All connector
numbers
1 Ind: 4
FS=1
Type: L2 P052 = 3
P051 = 40
Offline
P176
*
FDS
(G162)
Source for variable Integration time [SW 1.8 and later]
The content of the selected connector acts as the integration time for the
current controller after multiplication with P156.
All connector
numbers
1 Ind: 4
FS=1
Type: L2 P052 = 3
P051 = 40
Offline
P180
FDS
(G160)
Positive torque limit 1
-300.00 to 300.00
[%]
0.01% of rated motor
torque Ind: 4
FS=300.00
Type: I2 P052 = 3
P051 = 40
Online
P181
FDS
(G160)
Negative torque limit 1 -300.00 to 300.00
[%]
0.01% of rated motor
torque Ind: 4
FS=-300.00
Type: I2 P052 = 3
P051 = 40
Online