Siemens SIMOTRAS 6SG7050, Operating Instructions Manual

Page: 382 / 604

Parameter list 01.04
11-34
SIEMENS AG 6SG7000-0BA76
SIMOTRAS HD Operating Instructions
PNU Description Value range
[Unit] No. indices See
Change
P445
*
(G130)
Selection of level/edge for switch-on/crawling
Selection to define whether ON command must be input via terminal 37 or
the crane control and the crawling setpoint injected in response to a log. "1"
level or to a 0
→
1 transition
0 ON with log. "1" state at terminal 37 and
injection of crawling setpoint with binectors selected in P440 in
log. "1" state
1 ON in response to 0
→
1 transition at terminal 37 and
injection of crawling setpoint in response to 0
→
1 transition of
binectors selected in P440
With this setting, the ON command or injection command for
the crawling setpoint is stored. The memory is reset when the
binector selected in P444 switches to the log. "0" state.
0 to 1
1 Ind: None
FS=0
Type: O2 P052 = 3
P051 = 40
Offline
11.20 Position sensing with pulse encoder
See parameters P140 to P147 for pulse encoder definition
P450
*
FDS
(G145)
Resetting of position counter
0 Reset position counter OFF
1 Reset position counter with zero marker
2 Reset position counter with zero marker when LOW signal is
applied to terminal 39
3 Reset position counter when LOW signal is applied to terminal
39
Note: Counter resetting with P450 = 2 and 3 is executed in the hardware
and is not affected by how the binectors controlled by terminal 39 are
interconnected
0 to 3
1 Ind: 4
FS=1
Type: O2 P052 = 3
P051 = 40
Offline
P451
*
FDS
(G145)
Position counter hysteresis
0 Hysteresis for rotational direction reversal OFF
1 Hysteresis for rotational direction reversal ON (the first pulse
encoder input pulse after a change in rotational direction is not
counted)
0 to 1
1 Ind: 4
FS=0
Type: O2 P052 = 3
P051 = 40
Offline
P452
*
BDS
(G145)
Source for "Reset position counter" command [SW 1.9 and later]
Selection of binector to control resetting of the position counter .
0 = binector B0000
1 = binector B0001
etc.
All binector numbers
1 Ind: 2
FS=0
Type: L2 P052 = 3
P051 = 40
Offline
P453
*
BDS
(G145)
Source for "Enable zero marker counter" command [SW 1.9 and later]
Selection of binector to control enabling of the zero marker counter
0 = binector B0000
1 = binector B0001
etc.
All binector numbers
1 Ind: 2
FS=1
Type: L2 P052 = 3
P051 = 40
Offline
11.21 Connector selector switches
(see also Section 8, Function Diagram Sheet G124)
P455
*
(G124)
Source for inputs of connector selector switch 1 [SW 1.9 and later]
Selection of connectors for the input signals for connector selector switch 1.
0 = connector K0000
1 = connector K0001
etc.
All connector
numbers
1 Ind: 3
FS=0
Type: L2 P052 = 3
P051 = 40
Offline
P456
*
(G124)
Source for control of connector selector switch 1 [SW 1.9 and later]
Selection of binectors to control connector selector switch 1.
0 = binector B0000
1 = binector B0001
etc.
All binector numbers
1 Ind: 2
FS=0
Type: L2 P052 = 3
P051 = 40
Offline