Siemens SIMOTRAS 6SG7050, Operating Instructions Manual

Page: 355 / 604

01.04 Parameter list
SIEMENS AG 6SG7000-0BA76
11-7
SIMOTRAS HD Operating Instructions
PNU Description Value range
[Unit] No. indices See
Change
r011
(G112)
Display of status of binary outputs
Representation on operator panel (PMU):
3 2 1 0 4 5 6 7
8 9 10 11 12 13 14 15
Segment ON: Corresponding terminal is activated
(HIGH level is applied) or overloaded or short-circuited
Segment OFF: Corresponding terminal is not activated
(LOW level is applied) or not overloaded or not short-
circuited
Display of status of binary output terminals:
Segment or bit
0 .... Terminal 46
1 ..... Terminal 48
2 ..... Terminal 50
3 ..... Terminal 52
7 ..... Terminal 109/110
Display of overloading of binary outputs:
Segment or bit
8 .... Terminal 46
9 ..... Terminal 48
10 ... Terminal 50
11 ... Terminal 52
12 ... Terminal 26 (15V output)
13 ... Terminal 34, 44 or 210 (24V output)
Ind: None
Type: V2
P052 = 3
r012
(G185)
Motor temperature
Display of motor temperature when a KTY 84 temperature sensor is
connected (P490.x=1).
A value of "0" is always output in r012 when a PTC thermistor or no
temperature sensor is installed.
i001: Motor temperature 1 (sensor at terminals 22 / 23)
i002: Motor temperature 2 (sensor at terminals 204 / 205)
-58 to +200
[°C]
1°C Ind: 2
Type: I2 P052 = 3
r013 Heatsink temperature
Display of heatsink temperature
-47 to +200
[°C]
1°C Ind: None
Type: I2 P052 = 3
r014 Temperature rise
i001: Calculated motor temperature rise (see P114)
i002: Calculated thyristor temperature rise (see P075)
0.0 to 200.0
[%]
0.1% Ind: 2
Type: O2 P052 = 3
r015 Display of line voltage
(generated as arithmetic rectification average, RMS value display applies to
sinusoidal voltage, average over 3 line-to-line voltages)
0.0 to 2800.0
[V]
0.0V Ind: None
Type: O2 P052 = 3
r017 Display of line frequency 0.00 to 120.00
[Hz]
0.01Hz Ind: None
Type: O2 P052 = 3
r018
(G163)
Display of firing angle 0.00 to 180.00
[degrees]
0.01 degrees Ind: None
Type: O2 P052 = 3
r019
(G162)
Display of actual motor current value
The internal actual motor current value is displayed (arithmetic average
between 6 current peaks)
-400.0 to 400.0
[% of P100]
0.1% of P100 Ind: None
Type: I2 P052 = 3
r020
(G162)
Display of the absolute value of motor current setpoint 0.0 to 300.0
[% of P100]
0.1% of P100 Ind: None
Type: I2 P052 = 3
r021
(G160)
Display of torque setpoint after torque limitation
Steps: 1
=
∧
0.1% of rated motor torque
-400.0 to 400.0
[%]
0.1% (see column
on left) Ind: None
Type: I2 P052 = 3
r022
(G160)
Display of torque setpoint before torque limitation
Steps: 1
=
∧
0.1% of rated motor torque
-400.0 to 400.0
[%]
0.1%(see column on
left) Ind: None
Type: I2 P052 = 3