Sices GC250 Technical Manual Download Page 55

Page: 55 / 145

EAAM057608EN

GC250 Technical Manual 55

7.3

LED OFF

LED steady ON

LED flashing







Signalling

Function



Indicates that the operation mode is

OFF/RESET



Indicates that you are accessing the

PROGRAMMING



The Gen-set control module is in another operating mode.

AUTO



Indicates that the operation mode is

AUTOMATIC



Flashing at 50% indicates that the operating mode is

TEST

Flashing at 90% indicates that the operating mode is

REMOTE

START



The Gen-set control module is in another operating mode.

MANUAL



Indicates that the operation mode is

MANUAL



Indicates that the operation mode is

MANUAL

and that the

protected start mode is active.



The Gen-set control module is in another operating mode.

ALARM



Indicates the presence of at least one lockout, one deactivation
or power-off



There is at least one active warning.



No anomalies.

ENGINE

RUNNING



Indicates engine running



Indicates engine idle

Summary of Contents for GC250


















































































































































Search results

Summary of Contents for GC250

Reviews:

Related manuals for GC250

Brands by name

Popular brands

Sices GC250, Technical Manual

Search results

Summary of Contents for GC250

Reviews:

Related manuals for GC250

Brands by name

Popular brands