Section 05 ELECTRICAL SYSTEM
Subsection 07 (GAUGE)
PROCEDURES
INFORMATION CENTER
Information Center Overview
The information center (cluster) is a multifunction
gauge that supplies several real time useful infor-
mations to the driver.
The information can be displayed in three lan-
guages (English, French, or Spanish).
Units of measurement can be displayed either
in Imperial system or in the metric system. Use
B.U.D.S. to change the language and units of
measurement settings.
The operator can view at a glance several indica-
tions such as speed, engine RPM, fuel quantity
and engine temperature. The gauge can also
be used to navigate through and select several
gauge functions, system modes of operation, and
to change certain settings and system parame-
ters.
Indicator lamps advise the operator of selected
functions or abnormalities.
The gauge itself is an electronic module. Both the
left and right handlebar switches send input sig-
nals to the gauge. The gauge interprets the sig-
nals from the switches and translates the signals
into the appropriate CAN (protocol).
The translated information is then sent out of the
gauge through the CAN bus to the appropriate
module so that it can initiate the specific action
commanded.
In addition, the gauge receives CAN signals from
other modules and is able to translate those sig-
nals into the appropriate gauge display.
The inputs to the gauge include but are not limited
to, the VTS, iS, MODE/SET, UP/DOWN arrows,
cruise and fuel level sensor.
The gauge incorporates a GPS (Global Positioning
System) that it uses for compass and speedome-
ter indications, and to provide speed signals to
other systems as required for their operation.
The beeper is also incorporated in the information
center.
Self Test Function
When the START/STOP button is pressed mo-
mentarily and the vehicle powers up, all LCD
segments and indicator lights in the information
center will turn
ON for 3 seconds
(self test func-
tion). This self test function allows the driver
time to ensure that all indications are functioning
properly.
It also validates the information centers internal
circuits, however, this does not validate proper op-
eration of the individual external circuits and sen-
sors that provide inputs to the information center.
If a system fault is detected by the ECM, the ap-
plicable message and/or indicator light will be dis-
played, and a beep code may be heard.
If the safety lanyard is not installed, the indications
in the information center will shut off a few sec-
onds after the self test function, but the electrical
system power stays on for approximately 3 min-
utes. Installing the D.E.S.S. key on its post will
turn the indications back on.
NOTE:
If the START/STOP button is pressed and
held without the D.E.S.S. key installed, the infor-
mation center will stay on as long as the START
button is held.
334
smr2009-036
Summary of Contents for GTX Limited iS 255 2009
