Section 03 ELECTRONIC MANAGEMENT SYSTEMS
Subsection 04 (MONITORING SYSTEM AND FAULT CODES)
FAULT
CODE
MODULE
DESCRIPTION
POSSIBLE CAUSE
SERVICE ACTION
P0113
ECM
Intake manifold
temperature sensor
open circuit or
shorted to battery
Damaged sensor,
damaged circuit wires,
damaged connector or
damaged ECM pins
Check the sensor for approximately
2280 to 2736 ohms at 19 to 21°C
(66 to 70°F).
Check for approximately 2280 to
2736 ohms at 19 to 21°C
(66 to 70°F) between ECM
connector pins A-H3 and A-J3.
Refer to the Service Manual for more
details.
P0116
ECM
Engine temperature
sensor functional
problem
Damaged sensor,
damaged circuit wires,
damaged connector or
damaged ECM pins
Check for debris or blockage in
cooling system.
Check the sensor for approximately
2280 to 2736 ohms at 19 to 21°C
(66 to 70°F).
Check for approximately 2280
to 2736 ohms at 19 to 21°C
(66 to 70°F) between ECM
connector pins A-A1 and A-J2.
Refer to the Service Manual for more
details.
P0117
ECM
Engine temperature
sensor voltage too
low
Damaged sensor,
damaged circuit wires,
damaged connector or
damaged ECM pins
Check for debris or blockage in cooling
system.
Check the sensor for approximately
2280 to 2736 ohms at 19 to 21°C
(66 to 70°F).
Check for approximately 2280
to 2736 ohms at 19 to 21°C
(66 to 70°F) between ECM
connector pins A-A1 and A-J2.
Refer to the Service Manual for more
details.
P0118
ECM
Engine temperature
sensor voltage too
high
Engine overheated or
damaged sensor
Check for debris or blockage in cooling
system.
Check the sensor for approximately
2280 to 2736 ohms at 19 to 21°C
(66 to 70°F).
Check for approximately 2280 to
2736 ohms at 19 to 21°C
(66 to 70°F) between ECM
connector pins A-A1 and A-J2.
Refer to the Service Manual for more
details.
P0122
ECM
TAS (Throttle
Accelerator sensor) 1
fault (short circuit to
GND)
Damaged sensor,
damaged circuit wires,
damaged connector or
damaged ECM pins
Check system circuits B-E1, B-K1, B-K3.
Check for 0 volt on sensor
connector pin E.
Check for 5 volts on sensor
connector pin D.
Check for 0.5 to 3 volts on sensor
connector pin F.
Refer to the Service Manual for
more details.
198
smr2009-029
Summary of Contents for GTX Limited iS 255 2009
