ROJ PCS 200 Original Instructions Manual Download Page 50

Page: 50 / 112

User Manual

PCS 200 Kit

- 3.9 -

3.5

MACHINE CONFIGURATION

This window allows to set the machine up during production at the manufacturer

’

premises.
The setup settings of the machine can be modified only by the Manufacturer

’

Production dpt.

or by the

Technical Support

Path:



Machine

Tab

Field

Description

It enables the row markers. The following operation modes are
available:

•

OFF

•

Trameline (Described in Setup)

•

Foldable machine

•

Plot seeding

It enables the push/pull sensors

It allows to select the machine speed sensor:

Single sensor (phonic wheel)

Double sensor (phonic wheel + index)

Radar

(If selected, the user is asked to turn off and restart the system from
the main disconnect switch/battery disconnect switch)

When selecting

“

Double sensor

”

you need to specify the number of

teeth of the phonic wheel (= number of pulses of the wheel between

Summary of Contents for PCS 200

















































































































Search results

Summary of Contents for PCS 200

Reviews:

Related manuals for PCS 200

Brands by name

Popular brands

ROJ PCS 200, Original Instructions Manual

Search results

Summary of Contents for PCS 200

Reviews:

Related manuals for PCS 200

Brands by name

Popular brands