ROJ PCS 200 Original Instructions Manual Download Page 14

Page: 14 / 112

General information

- 1.4 -

PCS 200 Kit

1.2.3 Machines on which the integration of the mentioned partly

completed machinery is foreseen

•

Pneumatic and precision seeders for tractors NOT equipped with ISOBUS
connection.

•

Pneumatic and precision seeders for tractors equipped with ISOBUS connection.

☞

The current version of the system is based on a proprietary architecture and DOES
NOT include the ISOBUS connection (foreseen for the coming versions).

1.2.4 Acronyms used

EHSR

Essential Health and Safety Requirement of Annex I of Machinery
Directive

Performance Level (level of reliability of the safety functions) according to
EN 13849-1

Analog/Digital Converter

CAN

Controller Area Network (BUS)

ECU

Electronic control unit

ISOBUS

Communication standard for tractors and machinery for agriculture and

forestry ISO-11783

Motor with integrated drive

PTO

Power take-off

SDB

Sub distribution board

HMI

Human-Machine Interface console

Summary of Contents for PCS 200

















































































































Search results

Summary of Contents for PCS 200

Reviews:

Related manuals for PCS 200

Brands by name

Popular brands

ROJ PCS 200, Original Instructions Manual

Search results

Summary of Contents for PCS 200

Reviews:

Related manuals for PCS 200

Brands by name

Popular brands