ROJ PCS 200 Original Instructions Manual Download Page 86

Page: 86 / 112

User Manual

PCS 200 Kit

- 3.45 -

ECI software update

Path:



Selecting the desired software from the list and pressing the

button, it is possible

to update the ECU software.

Remarks:

After the ECU software update it is possible that an

“

Invalid protocol version

”

error is displayed. In that case, just go on with the updating procedure: the
error is deleted after the HMI has been updated too.

After the ECU software update, it is possible that one ore more errors are

displayed according to the previously installed software version, as follows:

Configuration and setup parameters lost
Invalid configuration or MD address
Data checksum
Invalid checksum

In that case, follow the procedure described in the next paragraph in order
to confirm the addressing and to restore the parameters.

How to confirm the addressing and restore parameters

Close the alarms window via the green check mark. The

“

MD Addressing

”

opens.

Wait 10 seconds before pressing the

“

Addressing

”

button.

Summary of Contents for PCS 200

















































































































Search results

Summary of Contents for PCS 200

Reviews:

Related manuals for PCS 200

Brands by name

Popular brands

ROJ PCS 200, Original Instructions Manual

Search results

Summary of Contents for PCS 200

Reviews:

Related manuals for PCS 200

Brands by name

Popular brands