ROJ PCS 200 Original Instructions Manual Download Page 24

Page: 24 / 112

Installation

- 2.4 -

PCS 200 Kit

2.4 DMD2

2.4.1 Outlet shaft torque, speed and axial/radial loads

The following features refer to the geared motor outlet shaft (slow shaft) dimensions.
Designed for 12V agricultural equipment

•

4,5 Nm, 80 rpm @ outlet shaft (54T01099)

•

Built-in driver for the brushless motor

•

2 digital inputs

•

Axial load allowed: 100N

•

Radial load allowed: 200N

2.4.2 Overall dimensions of the geared motor and dimensions of the

outlet shaft

The geared motor outlet has got a shaft aligned with the fast shaft of the electric
motor.
The dimensions are shown in the technical drawing below.

Figure 2-5

–

Outlet shaft dimensions

For further information, make reference to

TD_DMD2_revI.pdf

Summary of Contents for PCS 200

















































































































Search results

Summary of Contents for PCS 200

Reviews:

Related manuals for PCS 200

Brands by name

Popular brands

ROJ PCS 200, Original Instructions Manual

Search results

Summary of Contents for PCS 200

Reviews:

Related manuals for PCS 200

Brands by name

Popular brands